banner



how to fix stripped screw hole

How to fix stripped plastic screw holes?

Old 02-28-2009, 06:55 PM

Senior Member

Thread Starter

My Feedback: (1)

Join Date: Jul 2008

Location: Strathmore, AB, CANADA

Posts: 147

Likes: 0

Received 0 Likes on 0 Posts

Default How to fix stripped plastic screw holes?


How to fix stripped plastic screw holes?

IvanG is offline

Old 02-28-2009, 06:57 PM

Senior Member

My Feedback: (1)

Montana Mike's Avatar

Join Date: Jul 2008

Location: Helena, MT

Posts: 912

Likes: 0

Received 1 Like on 1 Post

Default RE: How to fix stripped plastic screw holes?


I have put a few drops of CA glue on a tooth pick and rubbed the toothpick on the inside of the stripped hole. wait a few hours and do it again.

Montana Mike is offline

Old 02-28-2009, 07:04 PM

Senior Member

DaveG55's Avatar

Join Date: Jan 2005

Location: Stockbridge, GA

Posts: 8,275

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?


I usually shave a small length of plastic about the size of a tooth pick and superglue it into the hole. Others have filled the hole with stuff like JB Weld and redrilled the holes after it dries. Still others just apply superglue to the screw, tighten it as much as possible (works best if the hole is not completely stripped out) and let it dry in place.

DaveG55 is offline

Old 02-28-2009, 07:05 PM

Senior Member

Join Date: Jun 2007

Location: Gold CoastQueensland, AUSTRALIA

Posts: 682

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?


Use slightly larger screws

stussman is offline

Old 02-28-2009, 08:02 PM

Senior Member

Thread Starter

My Feedback: (1)

Join Date: Jul 2008

Location: Strathmore, AB, CANADA

Posts: 147

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?


I did the larger screw, but it only worked one time. And now they are stripped again

IvanG is offline

Old 02-28-2009, 08:05 PM

Senior Member

Sugafree's Avatar

Join Date: Oct 2006

Location: ontario, ON, CANADA

Posts: 2,184

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?


Plastic parts are Cheap.......Swap them out with New ones......(Then Try not to Over tighten the Screws that go into Plastic next time)

Sugafree is offline

Old 02-28-2009, 08:30 PM

Senior Member

SAVAGEJIM's Avatar

Join Date: Jul 2005

Location: Torchy the Fiery Fast RC Turtl

Posts: 10,544

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?



ORIGINAL: IvanG

I did the larger screw, but it only worked one time. And now they are stripped again

All have a myriad of fixes for refurbishing the scre hole in the plastic. These are okay, but they are alot of the times not like the original. The best remedy I have hear is to simply replace the piece altogether.

If you must insist on keeping the piece, if room ermits, you can dispense with the wood-like screws (like the Z569) and go with a nut and bolt instead. Just put the bolt in and screw in the nut behind it, loc tite that, and as the Frecnh say, voila!

SAVAGEJIM is offline

Old 02-28-2009, 09:49 PM

Senior Member

Savage_mt2_Attack's Avatar

Join Date: Feb 2007

Location: Gibbons, AB, CANADA

Posts: 249

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?


Put a length of zip tie in the hole and then just tighten the screw is as you normally would. I have done this on multiple holes, in fact 3 out of the 4 lower transmission mount holes are fixed by this on my truck

Savage_mt2_Attack is offline

Old 02-28-2009, 10:04 PM

Senior Member

Thread Starter

My Feedback: (1)

Join Date: Jul 2008

Location: Strathmore, AB, CANADA

Posts: 147

Likes: 0

Received 0 Likes on 0 Posts

Default RE: How to fix stripped plastic screw holes?


hah thats the kind of fix i was looking for, on the fly! thank you !

IvanG is offline

Old 11-05-2013, 12:02 PM

Junior Member

Join Date: Nov 2013

Posts: 1

Likes: 0

Received 0 Likes on 0 Posts

Default


Originally Posted by Savage_mt2_Attack View Post

Put a length of zip tie in the hole and then just tighten the screw is as you normally would. I have done this on multiple holes, in fact 3 out of the 4 lower transmission mount holes are fixed by this on my truck

I have no idea what this site is all about but I found this via google and registered just to reply to this post. I have a pool valve with stripped screw holes from a too heavy valve actuator that are causing a leak. To "Replace the plastic part" would be a huge undertaking given the location and the configuration of the PVC plumbing. I have searched high and low for a simple solution that would work in this difficult environment and then I saw this. I had just cut a zip tie that was holding excess control line to my valve so everything that I needed for this fix was already staring me in the face, and so far, it works like a champ! THANKS!

turtleator is offline

Old 03-24-2014, 10:20 PM

Senior Member

Join Date: Jan 2007

Location: San Bruno, CA

Posts: 144

Likes: 0

Received 0 Likes on 0 Posts

Default


Originally Posted by Savage_mt2_Attack View Post

Put a length of zip tie in the hole and then just tighten the screw is as you normally would. I have done this on multiple holes, in fact 3 out of the 4 lower transmission mount holes are fixed by this on my truck

DUDEEEEEE thank you so much for this tip; i was about to fill the holes with JB weld and redrill them but this was sooooo much easier.

helicub81 is offline

Old 04-18-2014, 07:03 AM

Senior Member

Join Date: Nov 2006

Location: butler, PA

Posts: 290

Likes: 0

Received 0 Likes on 0 Posts

Default


We used to save the plastic "tree's" from the parts that came in kits. If you stripped a hole, you'd cut a length of the tree off, drill a bigger hole, glue or epoxy it in, drill new screw hole. It worked very well because you were using the same plastic the part was made from.

pcarluvr is offline

Old 06-01-2014, 09:02 PM

Senior Member

Join Date: Aug 2011

Location: Morris Plains, NJ

Posts: 147

Likes: 0

Received 0 Likes on 0 Posts

Default


Originally Posted by pcarluvr View Post

We used to save the plastic "tree's" from the parts that came in kits. If you stripped a hole, you'd cut a length of the tree off, drill a bigger hole, glue or epoxy it in, drill new screw hole. It worked very well because you were using the same plastic the part was made from.

Huh. I like that.

Team GxG is offline

Old 04-07-2015, 08:33 PM

Junior Member

Join Date: Apr 2015

Posts: 1

Likes: 0

Received 0 Likes on 0 Posts

Default


Dude, Thanks so much for the idea. Solved my problem. I actually found this post searching for a way to fix some stripped out holes in a freezer door handle. Would have cost me $50-75 for a new handle if I could find one in stock. A few cable tie clippings in the hole held fast, at least for now. Again...thanks!

Igpajo is offline

Old 09-03-2019, 07:03 AM

Junior Member

Join Date: Sep 2019

Posts: 1

Likes: 0

Received 0 Likes on 0 Posts

Thumbs up


Originally Posted by Savage_mt2_Attack View Post

Put a length of zip tie in the hole and then just tighten the screw is as you normally would. I have done this on multiple holes, in fact 3 out of the 4 lower transmission mount holes are fixed by this on my truck :)

I�ve been trying to figure out a solution all weekend. Savage, this worked perfectly! Thank you so much!!

FrozenPlasma is offline

Old 09-05-2019, 06:18 AM

1QwkSport2.5r's Avatar

Join Date: Oct 2006

Location: Cottage Grove, MN

Posts: 10,017

Default


A drop or two of CA glue on the screw and seating the screw works pretty well too. Wait a day or two before snugging the screw the rest of the way.

1QwkSport2.5r is offline

Old 12-22-2019, 04:41 PM

Join Date: Jun 2006

Location: Houston, TX

Posts: 58

Likes: 0

Received 0 Likes on 0 Posts

Default


Fast way, like I do on airplanes. For plastic squirt denatured alcohol first and try to clean. Then scratch up inside with xacto knife or something. Couple drops of CA. Squirt kicker in and thread screw in then out. Repeat 5 or 10 times real quick.

stevens4x is offline

Old 05-08-2020, 11:34 PM

-SomeGuy-'s Avatar

Join Date: Nov 2005

Location: Montreal, QC, CANADA

Posts: 3,741

Received 0 Likes on 0 Posts

Default


The zip tie trick is the only one you need in a pinch. Works on pretty much anything.

-SomeGuy- is offline

Old 05-09-2020, 02:30 AM

Join Date: Jun 2005

Location: , NY

Posts: 257

Likes: 0

Default


From all the methods I've seen mentioned here, the screw hole problem should be successfully fixed many times over, but just in case there is still a craving for another way to do it...
Fill the screw hole with baking soda, add a drop of thin CA to saturate the powder and you're instantly ready to drill a new pilot hole for the screw.

airsteve172 is offline

Old 06-21-2020, 10:46 AM

Junior Member

Join Date: Jun 2020

Posts: 1

Likes: 0

Received 0 Likes on 0 Posts

Default


Originally Posted by turtleator View Post

I have no idea what this site is all about but I found this via google and registered just to reply to this post. I have a pool valve with stripped screw holes from a too heavy valve actuator that are causing a leak. To "Replace the plastic part" would be a huge undertaking given the location and the configuration of the PVC plumbing. I have searched high and low for a simple solution that would work in this difficult environment and then I saw this. I had just cut a zip tie that was holding excess control line to my valve so everything that I needed for this fix was already staring me in the face, and so far, it works like a champ! THANKS!

I had to replace a Hayward Multiport valve assembly with handle for the top of my Hayward Sand filter on my pool. It was basically the cheapest way to get a new gasket replacement since it was already glued to the entire assembly. To reattach this assembly, of which you may be familiar, was to screw 6 screws back into the main portion of the top of the sand filter. The very last screw I put back, I found the hole was stripped. I tried different screws in the same hole and nothing worked. In the process of picking the old part back up, a piece of black plastic fell out of that original hole. This told me the hole had been stripped out at the factory and reinforced with this piece of plastic, as I had never had this part off of the Hayward sand filter. Since this is a part of the pool equipment where a lot air pressure is involved, will the idea of the "zip tie" work to reinforce that one hole and still create the proper air pressure that I will need to operate the pool filter efficiently? I had hunted everywhere for a slightly larger machine screw, but could never find one. This fix appeals to me if I can still maintain the proper air pressure that is required to operate the pool without leaks. Counting on your opinion as an experienced pool owner and one who has used the zip tie fix....LOL.....Thanks!


Last edited by Brandy2424; 06-21-2020 at 10:51 AM.

Brandy2424 is offline


Posting Rules

You may not post new threads

You may not post replies

You may not post attachments

You may not edit your posts


HTML code is Off




how to fix stripped screw hole

Source: https://www.rcuniverse.com/forum/hpi-monster-truck-forum-250/8529299-how-fix-stripped-plastic-screw-holes.html

Posted by: nguyenbahe1939.blogspot.com

0 Response to "how to fix stripped screw hole"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel